The Midmark Ritter M9 Ultraclave Automatic Sterilizer was specifically designed and engineered to meet those needs automatically and quietly to dissipate the steam and provide fast and efficient drying of your instruments.The Ritter M9 has all the reliable sterilizing power you need. It is a compact unit, great for small spaces. With our strong heritage of quality, value and reliability, you can’t go wrong with the Ritter M9.The M9 is simple to use and effective. Select your cycle and the time is set for you. Press “Start” and the M9 fills with the correct amount of water. Once the sterilization process is complete, the door opens automatically. Powered by how to embed a youtube video and nya casinon utan spelpaus mga Ritter M9 FeaturesPulse-air Removal TechnologyThe M9’s Steam-Flush Pressure-Pulse Air Removal System is so efficient that it can pass the air removal tests required on more complex vacuum steam autoclave systems, thus ensuring good steam penetration for those challenging loads. Plus, less complexity means better reliability and a cost effective solution for your sterilization needs.Convenience at a GlanceThe LCD display indicates cycle selected, cycle temperature and exposure time. When the cycle enters sterilization mode, the temperature, pressure, and the remaining cycle time is displayed. Remaining cycle time is also displayed in the dry mode. Note: Temperature & pressure are not displayed during dry mode.No More Wet InstrumentsOnce the sterilization is complete, the door of the autoclave opens automatically and quietly to dissipate steam and dry your instruments. You’ll have dry, sterile instruments every time.Safety FeaturesIf the door is not closed completely or the reservoir water level is low, the LCD display will provide the appropriate message. In either case, sterilization will not continue until you’ve attended to the unit.Ease of Draining & FillingFor ease of draining and filling, the M9’s reservoir fill port and drain tube are in the front of the unit, not on top or in back.Optional Printer AccessoryThe M9 printer accessory provides a permanent record of cycle times, temperatures and pressures during a cycle.Self Program ControlsProgrammable controls allow for creation of different cycle parameters for special sterilization needs. Programmable buttons allow you to change the following: Exposure Time (3 to 90 minutes), Temperature (230 to 275°F), Dry Time (0 to 60 minutes), or Vent (slow or fast). The #1 and #2 buttons allow you to store the change if desired.Pre-Programed ControlsFour pre-programmed sterilization cycle controls: Unwrapped (132°C or 270°F for 3 minutes), Pouches (132°C or 270°F for 5 minutes), Packs (121°C or 250°F for 30 minutes), Handpieces (unwrapped and pouched) (132°C or 270°F for 6 minutes).LCD DisplayIndicates cycle selected, temperature and exposure time. During the cycle, the display shows messages describing status of cycle. When the cycle enters sterilization mode, remaining time is displayed as well as temperature and pressureSpecifications:Overall length: 18.81″ (47.8 cm)Overall width: 15″ (38.1 cm)Overall height: 16.44″ (41.8 cm)Countertop area: Minimum depth 18″ (45.7 cm)Chamber:9″ diameter (22.9 cm)15″ depth (38.1 cm)3.5 gal. usable volume (13.4 liters)Trays:2 large – 12″ L x 7.31″ W x .88″ D (30.5 x 18.6 x 2.2 cm)2 small – 12″ L x 5.62″ W x .88″ D (30.5 x 14.3 x 2.2 cm)Unit Weight: 75 lbs.Shipping Weight: 83 lbs.Shipping Box Dimensions: 24″ L x 21″ W x 21″ HWater reservoir capacity: .88 gal. (3.3 liters)ReferenceManufacturer InformationBrochures